The aim with my master thesis is to develop and test the applicability of methods to quantify and map solute advective travel times and pollutant transport at the catchment scale. Such quantification and mapping can increase the understanding of catchment-scale pollutant transport in general and contribute to the identification of the main sources of water pollution and the most efficient measures to reduce such pollution. The study area is the catchment of Oxundaån, about 20 km north of Stockholm. For detailed GIS modeling of water flow and catchment-scale contaminant transport in water, I´ve used new high-resolution elevation maps, land cover maps and soil maps combined with other available relevant data..

This report is a Master?s Thesis performed by Andreas Adolfsson and David Jacobsson atChalmers University of Technology. The purpose of this master?s thesis is to evaluate anew method for load-shedding, the voltage controlled underfrequency load-sheddingdeveloped by ABB. This report presents a comparison between conventionalunderfrequency load-shedding and this new method for load-shedding.

The aim of this study is to evaluate whether the value of occupant load is over or under estimated when the Swedish general value for department stores, 0,5 person/m2, is used for dimensioning shopping centers. The data that was analyzed derives from seven shopping centers and one department store. A conservative method was used to calculate the occupant load factor. The analysis shows that two groups can be discerned: one group that is characterized by a lower occupant load factor that does not exceed 0,3 person/m2, and one group with a higher occupant load factor. Shopping centers with a higher occupant load factor are located centrally in large urban areas.

Stormwater run-off from surfaces such as roads or rooftops is often polluted with heavy metals and nutrients. Many of these substances can cause great damage in biota if they end up in the recipient. In Sweden constructed wetlands and ponds for treatment of stormwater are frequently used, since research has shown that these treatment ponds are reducing stormwater pollution considerably to a low cost. The knowledge of these pollutant removal mechanisms and how follow-up and assessment of the ponds should be performed is still limited.To determine the pollutant removal efficiency of the stormwater ponds it is recommended that flow-weighted water samples are collected from both the inflow and the outflow of the pond. This method demands considerable resources of time and money for installations and analysis.

Syftet med denna undersökning har varit att underlätta för företaget Re-Load att presentera sin lastpall som produkt för potentiella kunder. Syftet har också varit att stötta Re-Load till att bli licenserad EUR-pall samt att successivt ersätta befintliga lastpallar och långsiktigt exekvera företagets affärsplan. Målet har varit att undersöka produkten avseende lönsamhet, miljöinverkan och hur den påverkade arbetsmiljön. Under-sökningen har genomförts med ett befintligt flöde där produkten använts och utifrån detta kunde en flödesstudie samt en komparativ produktstudie utföras med en alternativ lastpall. Med data hämtat ur detta flöde utfördes en investeringskalkylering, miljöberäkningar, subjektiva intervjuer samt dokumentation.

The river Göta Älv reaches between Vänern and Gothenburg and is the main raw water source for Gothenburg that supplies about 700 000 people with water. To protect and maintain a high water quality, continuously samples and water analyses are made throughout the river. In 1998 a protection area was founded between surte and Lärjeholm where the raw water intake is. This was made to increase the awareness of the importance to protect the water. However, there is a lot of contribution of untreated stormwater to Göta Älv within the protection area.Göteborg Water and Sewage Works commissioned this thesis where two areas, Tagene industrial area and Kärra residential area, with untreated stormwater outlets within the protection area are studied.

The aim of this study was to develop a load prognosis model for Uppsala district heating system to be used as a tool for heat production optimization. The methodwas to build three models for the different customer types; housing, industry andoffices and then scale them for the total system using data from Uppsala districtheating system. The heat load consists of two parts, one that is temperaturedependent and one that is dependent of the social behavior of the customers. Thetemperature part was modelled with an ARX model using an outdoor temperatureprognosis as input signal. The social behavior part was modelled using the mean ofthe social behavior from some days before and additionally by distinguishing betweenweekdays and weekends.

The purpose of this thesis has been to develop a tool for modelling and simulating the nuclear plant Ringhals 3. The model should be used to improve the knowledge on the dynamics of the plant. Ringhals 3 is being upgraded to produce more power and a tool for analyzing the new operating conditions is needed.The work in this thesis has consisted of improving and developing an existing model of Ringhals 3 made with the modelling tool Dymola. The model has been validated by comparing the results of a simulated house load transient with data from the actual plant. Validation shows good agreement with data from the real plant.

The purpose of this thesis has been to develop a tool for modelling and simulating the nuclear plant Ringhals 3. The model should be used to improve the knowledge on the dynamics of the plant. Ringhals 3 is being upgraded to produce more power and a tool for analyzing the new operating conditions is needed.The work in this thesis has consisted of improving and developing an existing model of Ringhals 3 made with the modelling tool Dymola. The model has been validated by comparing the results of a simulated house load transient with data from the actual plant. Validation shows good agreement with data from the real plant.

The purpose of this thesis has been to develop a tool for modelling and simulating the nuclear plant Ringhals 3. The model should be used to improve the knowledge on the dynamics of the plant. Ringhals 3 is being upgraded to produce more power and a tool for analyzing the new operating conditions is needed.The work in this thesis has consisted of improving and developing an existing model of Ringhals 3 made with the modelling tool Dymola. The model has been validated by comparing the results of a simulated house load transient with data from the actual plant. Validation shows good agreement with data from the real plant.

There are many old dams in Sweden and, since few dams are constructed today, the main task in risk assessment on the existing dams is often to reduce the risk of failure. RIDAS (Swedish Guidelines on Dam Safety) is used when designing new dams and assess the existing ones. The guidelines include stability requirements for different failure modes, e.g. overturning and sliding, which imply that the load effect from e.g. uplift and ice load need to be less than the resisting loads or moments.

The purpose of this thesis has been to develop a tool for modelling and simulating the nuclear plant Ringhals 3. The model should be used to improve the knowledge on the dynamics of the plant. Ringhals 3 is being upgraded to produce more power and a tool for analyzing the new operating conditions is needed.The work in this thesis has consisted of improving and developing an existing model of Ringhals 3 made with the modelling tool Dymola. The model has been validated by comparing the results of a simulated house load transient with data from the actual plant. Validation shows good agreement with data from the real plant.

The purpose of this thesis has been to develop a tool for modelling and simulating the nuclear plant Ringhals 3. The model should be used to improve the knowledge on the dynamics of the plant. Ringhals 3 is being upgraded to produce more power and a tool for analyzing the new operating conditions is needed.The work in this thesis has consisted of improving and developing an existing model of Ringhals 3 made with the modelling tool Dymola. The model has been validated by comparing the results of a simulated house load transient with data from the actual plant. Validation shows good agreement with data from the real plant.

The purpose of this thesis has been to develop a tool for modelling and simulating the nuclear plant Ringhals 3. The model should be used to improve the knowledge on the dynamics of the plant. Ringhals 3 is being upgraded to produce more power and a tool for analyzing the new operating conditions is needed.The work in this thesis has consisted of improving and developing an existing model of Ringhals 3 made with the modelling tool Dymola. The model has been validated by comparing the results of a simulated house load transient with data from the actual plant. Validation shows good agreement with data from the real plant.

The purpose of this thesis is to examinethe possibilities for adding a floor to anexisting building using the two materialswood and sheet metal profiles as the loadbearing structure. An apartment buildingfrom the 60s has been used as referencehouse. Two different suggestions for thedesign are presented in the rapport. Oneof them has been analyzed with wood andsheet metal as the load bearing structure.Using the old constructional calculationsand blueprints of the existing buildings,the load bearing capacity has beencalculated. In the calculation programFEM-Design the building has been testedwith the loads that an extra floor wouldgive.